lockup

英 [ˈlɒkʌp]

美 [ˈlɑˌkʌp]

n.  同 jail; (不与车主房子相连的)车库

COCA.21639

柯林斯词典

• N-COUNT 同jail
  Alock-upis the same as ajail.
  1. ...the 450 inmates at the maximum-security lock-up in Lucasville.
     被关在卢卡斯维尔一级警戒监狱的450名囚犯
• N-COUNT （不与车主房子相连的）车库
  Alock-upis a garage that is used by someone, but is not next to their house.
  1. 25lb of Semtex explosive was found in the lock-up she had rented to Mr Henderson.
     在她租给亨德森先生的车库里发现了25磅塞姆汀塑胶炸药。
  2. Lock-upis also an adjective.
     
  3. ...a lock-up garage.
     独立车库

英英释义

noun

• the act of locking something up to protect it
  Synonym:locking
• jail in a local police station

双语例句

• How are your contacts in chemical lockup?
  能找你那个化工品朋友帮个忙吗？
• The developer needs to determine when to halt timeouts and retries to avoid system lockup resulting from consumption of all resources waiting on slow or failed services.
  开发人员需要确定何时停止超时和重试，以避免使用所有等待缓慢或故障服务的组件所导致的系统锁定。
• A mathematical dynamic model is set up and the effect of service and structure parameters upon stopping distance, braking time, and the time lag between front and rear wheel lockup is analyzed.
  文中建立了力学和数学模型，分析研究主要结构和使用参数对制动距离、制动时间和前、后轮抱死间隔时间的影响。
• And at some point, while you're in lockup.
  然后在某个时候，当你在牢里的时候。
• Through the results of the example optimization for gearbox ratios of an armored tracked vehicle which uses a turbocharged diesel engine and lockup hydrodynamic transmission, it is proved that this model is helpful in designing and improving the power performance and fuel economy of the vehicle.
  对以涡轮增压柴油机为动力装置、采用闭锁式液力传动的某型装甲履带车辆的变速箱挡比进行了试优化，证明该方法能够为设计及改进车辆动力性和燃油经济性提供参考。
• Based on the assumption that first-day IPO underpricing could generate information momentum and thereby increasing demands for the new issuing stocks, this paper models the relationship between lockup period and IPO underpricing.
  基于IPO首日抑价可以产生信息动量效应，进而增加二级市场对新股需求的假设，建立了锁定期与IPO抑价关系模型。
• A set of test methods for turning the brake power distribution with lockup characteristics and drive stability of a vehicle brake system during brake system design and development are introduced in the paper by using a small passenger car as am example.
  文章以小型乘用汽车为例，主要介绍了汽车制动系统设计开发过程中，为确定影响制动力分配和车轮抱死特性的各项参数而设计的一套标定匹配试验方法。
• The measures for improving wear of camber for lockup were proposed.
  针对锁紧弧面的磨损提出了改善措施。
• The refugees are threatening to break into the food lockup.
  难民们还威胁要抢粮仓。
• Geneva mechanism in glassware printing machine was investigated. The main factors influencing precision of movement of geneva mechanism and the influence of wear of camber for lockup on precision of orientation in operation were analyzed and calculated.
  以玻璃器皿套色印花机中的槽轮机构为研究对象，分析了影响其运动精度的主要因素以及槽轮机构锁紧弧磨损对工作定位精度的影响，并做出了相应的计算；